Dwin HDP-500 Betriebsanleitung

HDP-500 SUPERDATA PROJECTION MONITOR Installation and Operating Instructions Read these instructions completely before operating t

10 of 29 The remote control supplied with the unit is factory programmed to operate the HDP-500 when “TV” mode is selected. SL-8000 remote furnis

11 of 29 At this point you are ready to proceed with the initial adjustment of the unit. Make certain that the power and signal connections have bee

12 of 29 Press “1” to view the focus screen. Note that the screen will display the Focus menu against a background of the crosshatch/dot pattern.

13 of 29 Geometry Adjust Menu Geometry is the series of adjustments that correctly align the picture scans to the size of the screen. Just as im

14 of 29 directly to the next step, or press “MENU” to exit. Center Pin Look at the lines that intersect the center of the screen and use the /

15 of 29 Tilt At the Tilt screen, use the / and / buttons to adjust center horizontal and vertical lines parallel to the screen edges

16 of 29 RED GEOMETRY The adjustments for Red Geometry are similar to those used to set the Green Geometry, except that instead of using th

17 of 29 As with the Red Geometry, these adjustments will be to a master setting previously established. This time the blue will be adjusted to the

18 of 29 The coarse convergence is centered in nine areas around the edges of the raster and at the center of the image. The convergence is adjuste

19 of 29 When all nine coarse convergence points have been converged press “2” to move to Fine Convergence. Fine Red Convergence Once the basic Co

2 of 29 Table of Contents Safety Information ___________3 Important Information for the User___________________4 Specifications ___________

20 of 29 The next screen will instruct you to type the word “YES”. Do this using the up and down / arrow buttons on the remote as the letters chan

21 of 29 Finally, set the Red and Blue gain controls so that the far right bar is as bright as possible while maintaining an even step of gray from

22 of 29 To center the picture, press “MENU” to display the Main Menu, and then press “4” to access the Centering screen. When the Centering scree

23 of 29 To name the source, use the  and  arrow buttons on the remote to cycle through the alphanumeric characters. When the first character is s

24 of 29 This will bring the highlight down to item 2, “Menu Access”, where “Enabled” is normally highlighted on the right side of the menu. This i

25 of 29 • High: This setting is roughly equivalent to a color temperature of 9,300° K . It will deliver the “brightest” picture at the expense of

26 of 29 3. Open the top cover by removing the two screws located on the front bezel above either side of the center lens. Remove the top cover b

27 of 29 When the set is installed, you should explain the basic operational controls to the user: power on/off (using either the remote or automati

28 of 29 When three channels have been focused, cover the blue lens with the lens cap and use the menu system to call up the Red Convergence patter

29 of 29 Limited Warranty This warranty protects the owner of HDP-500 for one (1) year from the date of purchase for labo

3 of 29 SAFETY INFORMATION 1. Read and apply all of the safety and operating instructions provided with your video equipment. 2. Keep all safe

30 of 29 You must pay shipping charges incurred in getting your product to the factory. We will pay the return shipping charges if the repairs are

4 of 29 extensive work by a qualified technician to restore the video equipment to normal operation. e. If the video equipment has been dropped or

5 of 29 SPECIFICATIONS AND TECHNICAL DATA System Description: Red, Green, Blue three CRT/lens large screen refractive projection system for vid

6 of 29 This manual contains the information required to properly install, configure, setup and operate the DWIN HDP-500 data projection monitor.

7 of 29 Planning a projection television installation is a critical part of the installation. Even with the extended range of mechanical and electro

8 of 29 Make the appropriate connections to the front panel, using the following descriptions as a guide. DWINHDP-500RED GREEN BLUE H/C

9 of 29 Before initial adjustments are made to the unit, locate the correct distance from the screen. This distance should be obtained by using the